Stomra · Guide
Precast elements
A precast element in Stomra is an ordinary wall with three things added: edge details, cast-in items and its reinforcement. Your assistant lays the elements out; you open one and review it.
A precast element is a wall
Stomra has no separate precast wall system and no precast mode. A precast wall element is a wall drawn with the Wall tool, with the layers its type gives it: a sandwich wall has an outer leaf, insulation and an inner leaf; a solid wall has one layer. One wall is one factory element. A long run is divided into elements with Split, which leaves a joint between them.
Three things turn such a wall into an element a factory can make:
Edge details
A named section swept along an edge: the ends, the top, the bottom, and the sides, head and sill of each opening.
Cast-in items
Lifting anchors, sleeves, fixing plates, sandwich ties and conduit, placed in the wall and moving with it.
Reinforcement
Mesh in each concrete layer, bars along edges and round openings, and the bars each cast-in product asks for.
Everything else stays as it is: openings, wall outlines, Split, bar sets, History and versions. Each element becomes a piece with its own shop drawing, as described in Shop drawings.
Edge details
An edge detail is a type in the project's catalogue. It is a small 2D section drawn across the wall at an edge, measured from the wall's exterior face and in from the edge. The section is made of regions, and each region does one of two things:
- It becomes a layer. A region marked as inner leaf, outer leaf or insulation replaces what was there. Next to a window, 100 mm of insulation becomes inner-leaf concrete: a thickening. A region outside the edge adds material: an outer leaf carried 270 mm past the end to cover the other element at a corner.
- It is cut. The region is taken away: a chamfer, a groove, a sealant slot.
The detail is swept along the whole edge, or along part of it. An opening's four details meet at its corners, and at the wall's corners the ends run full height while the top and bottom stop between them, so every corner is filled once. On a wall under a roof, a top detail follows each layer's own top as built, flat or sloped.
Because a detail is a type, changing it changes every wall that uses it. Quantities, weights, drawings and 3D all follow the new shape of the layers.
Edge details work on any layered wall, not only on concrete. A facade panel run on 25 mm below a timber wall's foot is a region past the bottom edge in the panel's layer.
Situations: the same detail for the same place
A precast project stays consistent when every edge of the same kind gets the same detail. Stomra reads each edge's situation from what it meets:
| Situation | Where |
|---|---|
| Joint | An end that meets another precast element in line |
| Outer corner, inner corner | An end that meets another element at a corner |
| T | An end that meets another element whose line goes on |
| Free end | An end that meets nothing |
| Opening side, head, sill | The edges of a door or window |
| Top, bottom | The top at a floor and the bottom on the foundation |
| Lift | A stretch of the top under each lifting anchor |
An edge detail type can say which situation it is for. The plan then puts it on every edge of that situation, and the check names any edge detailed differently from the project's other edges of the same situation.
Sandwich corners
At a corner of two sandwich elements, the insulation should go round the corner unbroken. The usual way is that one element runs through and carries the insulation round on its end, while the other ends a joint short of its face. Where the supplier instead laps the outer leaves, the project's corner rule is set to lapped and the plan proposes that corner instead. The check reads every end of a sandwich element from its actual shape and names insulation that shows, insulation that ends against the other element's leaf, and leaves that meet across the joint, which would be a cold bridge.
Cast-in items
A cast-in item is a component that sits in its wall. Its type says what it is and what shape it has:
- Block: a fixing plate, a box, a sleeve's former, by its width, height and depth.
- Bar: round, by diameter and depth: a lifting anchor, a sleeve.
- Lattice: a sandwich tie, two chords with a zigzag between them, standing across the insulation.
- Conduit: flexible conduit along a path through the wall, with rounded bends, counted by the metre.
The type can also hold the product (supplier and article), the layer the item must sit in (a lifting anchor in the bearing leaf, never in the insulation), its stated load, a recess former that cuts the wall round it, and an edge detail or a bar it brings with it.
Each item is placed in the wall's own frame: the face it looks out of (exterior, interior, top, bottom or an end), how far along the wall, how far up, and how far in from the exterior face. It can be turned, leaned at an angle, and repeated as a row with a count and a spacing. The Inspector shows these as the item's Cast-in item section, where you move, turn or lean it by hand.
Items move with their wall. Split hands each one to the element it stands in, flipping the wall keeps each in its layer, and deleting the wall deletes them. Loose parts that travel with an element but are not cast in (a threaded rod, a washer) can be added to its piece; the drawing lists them apart and leaves them out of the element's weight.
Weight, centre of gravity and lifting
Stomra weighs each element body by body, by its material: concrete at 2 400 kg/m³, stone wool at 100, EPS at 20, and so on. Edge details and openings change the bodies, so the weight, the concrete volume and the centre of gravity follow them.
Give the lifting anchors their stated load, as the supplier states it, and the check does two things: it compares the sum of the anchors' loads with the element's weight times the lifting factor (1.3 unless the project sets another), and it flags a centre of gravity that falls outside the anchors along the element. Both are flags for the engineer and the supplier to look at, never a design.
The project's rules
Each project keeps a few precast rules. They are starting values the organisation can change, never regulation:
| Rule | Starting value | Used for |
|---|---|---|
| Joint | 16 mm | The gap Split leaves between elements |
| Lifting factor | 1.3 | The lifting check |
| Smallest pier | 250 mm | The check of piers beside openings, and how far the plan keeps joints from them |
| Smallest lintel | 300 mm | The check of lintels over openings |
| Corner | Wrapped | How sandwich corners are proposed: wrapped or lapped |
| Longest, highest, heaviest element | None until set | The supplier's and the crane's limits; checked once given |
| Reinforcement | None until set | Mesh, bar size, grade, cover and anchorage for the plan's reinforcement |
Laying elements out with your assistant
Precast layout is done by your own assistant, Claude or ChatGPT, through the Stomra connector. Stomra hosts no AI of its own; see Modelling with AI for how the connector works. The precast work uses two tools, stomra_precast to read and stomra_precast_edit to write, followed by the shop drawing tools.
- Read. The assistant reads the elements, the catalogue of details, products and rules, each edge's situation, and the organisation's own examples in the Handbook.
- Plan, as a dry run. Stomra works out what it would do and writes nothing: splits for walls longer than the longest element, with joints kept clear of openings and of rows of cast-in items; a detail for every edge that has none, by situation; corners for sandwich walls; two lifting anchors for an element that has none; and the reinforcement, when the project has rules for it.
- You decide. What the plan cannot settle comes back as a list of questions, for example a corner where both elements run through, or a situation with two details to choose from. The assistant puts them to you instead of guessing.
- Apply. On your word the plan is written as one change: one Undo, one entry in History.
- Drawings. Each element becomes a piece with its mark and shop drawing.
- Check. Both tools check the result. The assistant fixes what they name, looks at the elements' drawings, and checks again.
Each proposal says why it stands where it does, such as the project's detail for a free end, or the Handbook example it came from. When an element has turned out well, the assistant can save it to the organisation's Handbook, with its details and products, so the next project starts from it.
The plan's lifting anchors are a starting layout: two in the top, either side of the centre of gravity, of the smallest product in the catalogue whose stated load is enough, clear of openings with a short lintel. The person and the supplier check them.
Reviewing an element
Nobody has to draw an element by hand, but a person opens it and reviews it. Select the wall and the Inspector shows:
- Edge details: each edge with its detail, and under it the reason the plan or the assistant gave. Pick another detail from the list to swap it, choose None to take it off, or use Add a detail on… for an edge that has none. A detail you pick by hand carries no reason, so the old one goes.
- Cast-in item, when you select an item: its face, place, turn, lean, count and spacing.
The Inspector also marks an item that does not sit in the layer its product asks for.
Reinforcement
When the project has reinforcement rules, the plan reinforces each element:
- mesh in each concrete layer, at both faces when the layer is thick enough, otherwise in its middle, cut to the layer as built;
- a bar along each edge of the layer;
- bars along the sides, head and sill of each opening, running on past the corners by an anchorage length;
- optionally U-bars closing a two-mesh layer's top and bottom;
- the bar each cast-in product asks for at each of its items, for example a bar through a lifting anchor's eye.
Bars you place yourself are ordinary bar sets in the wall and stay when the plan lays its own again. The element's shop drawing then carries a view of each concrete layer's reinforcement and the bar list. The amounts are the engineer's to decide; the rules are a habit to start from.
Hollow core and plattbärlag floors
Precast floors follow the same idea: the floor stays a floor, and its type's structural layer is the precast product.
Hollow core
- Every project has the seven published hollow core products, HD/F 120/19 to 120/50, as floor types, ready to draw with or to make a type with a topping from.
- The floor's panel division lays the 1 200 mm elements side by side across the span. The plan proposes one for a floor that has none, from the walls, beams or columns under its edges.
- Elements are marked HD101 and on by product, size and holes. Plans draw the joints, the marks and the span direction; a section across the span draws the cores; a 3D view that is not Coarse draws each element with its cores, joints and cut-back ends.
- The check names a bearing shorter than the product's, an end with nothing under it, an opening that takes an element's whole width or more than half of it, and an element with holes both at its edge and inside.
- An element schedule on a drawing lists mark, count, type, length, width and weight.
Plattbärlag
- The floor type has two layers: the topping, and under it the plate (PL 240/5 or PL/F 240/7). The lattice girders are stated on the product and drawn in sections.
- The division lays the plates as it lays hollow core, marked PL101 and on, and the seams go through the plate layer only.
- Where the plates end on a support inside the floor, an element joint cuts only the plate layer, so the topping runs on over the support. The plan asks about every wall or beam under the floor and offers the joint ready to add. Mark a partition as non-structural and it is not asked about.
- With reinforcement rules, the plan lays a strip of mesh over each seam, counted in sheets and following the division when it changes.
- The check names a plate bearing shorter than the product's own, an opening that cuts lattice girders, one that takes a plate's whole width, and seam mesh the rules ask for that is not laid.
What Stomra does not do
- No design. Not of elements, joints, lifting, hollow core or plattbärlag. The numbers are what is modelled, from the catalogue's values; spans, loads, holes and lifting are for the engineer and the supplier to approve.
- No regulation. Every limit comes from the project's rules and the products, and you can change them.
- Walls are straight. Edge details and cast-in items are for straight walls.
- Floors are drawn as a whole. Hollow core and plattbärlag elements appear on plans, sections and schedules, without a drawing of each element. Props and hollow core trimmers are not modelled.