Stomra Guides

Stomra · Guide

Walk mode

Walk through the model in first person, with game controls, the real sun and the site around you. Walk mode reads the model and never changes it.

Move W A S D walk Shiftrun Spacejump; hold to fly up Ccrouch Ffly, through walls PgUp PgDnlevel above, below Look the mouse looks around; the wheel sets the field of view ↑ ← ↓ → the arrows look too, for a laptop Do Eopen a door; turn a switch Xhide what you aim at (Z back) Kstructure and services only Vfirst or third person Mplan map: small, large, off Ptake a picture Lclay model or materials [ ]the sun ½ hour earlier, later
The keys you use most. Esc opens the menu, which lists them all.

Start a walk

  1. Open a 3D view and press Walk on the view, or choose Walk on the ribbon's View tab.
  2. A card shows the keys while the walk loads. Click (or tap) to start.
  3. The page goes full screen and takes the mouse. Move the mouse to look, and walk with W A S D.
  4. Press Esc for the menu, and Leave walk mode to go back to the model.

You start where the 3D view looks from. If a person is placed in the model (Annotate ▸ Person), the walk starts where they stand. A work order, a level or a room you choose under Go to starts you there too. A start spot inside a wall or a column moves to the nearest clear place on the same floor, and the walk says how far.

The walk shows what its 3D view shows, at the view's sun and with the view's lighting scene. What the view draws see-through is glass in the walk.

All the keys

KeyWhat it does
W A S DWalk.
Mouse, ← → ↑ ↓Look around. Click the view to give it the mouse again.
SpaceJump; hold it to fly up.
ShiftRun.
CCrouch; down when flying.
FFly, through walls; F again lands.
PgUp PgDnThe level above or below.
EOpen or close a door or window. On a switch, turn its lights.
X / ZHide what you aim at, for this walk / bring it back.
KStructure and services only; again for the whole building.
VFirst person, or third person with you in the picture.
MThe plan map: small, large, off.
PTake a picture of the view.
[ ]The sun half an hour earlier or later.
LClay model or materials.
WheelField of view.
EnterFull screen on or off, without stopping the walk.
HShow or hide the tips at the foot.
EscThe menu, with every key.

Some keys appear only where they apply: O and G for work orders, − +, 0–8 and T for versions, and B, N, , . to play the work phase by phase.

On a touch screen, the left thumb walks and the right thumb looks, with buttons to jump, crouch, fly and open doors; push the stick further to run. A gamepad works as well: the sticks walk and look, and its buttons jump, crouch, open doors, fly and take pictures.

How walking works

You walk on the model's own geometry: you stand on its floors, its stairs and the ground, and walls, glass and railings stop you.

What you see on screen

The site is around you: the ground as graded, pads in their own surfaces, the model's trees, shrubs and hedges in the wind, water, grass and birds, with steps and doors you can hear. A site without planting of its own gets generic trees around it, which the menu can turn off. See The site: place, ground and grading.

Esc pauses the walk and opens the menu: where to go on the left, settings on the right, and Walk on beside Leave walk mode at the foot.

PartWhat it holds
Go toThe levels and rooms, a larger plan map with the rooms' numbers and names, and, after a version step, what changed.
ViewFirst person, or third person with you in the picture.
LookClay model or Materials.
QualityLow, Medium, High or Ultra.
Plan mapSmall, large or off.
SettingsStructure and services only, Trees around the site, Sounds, Start in full screen, Invert up and down, Show the frame rate, and the turn speed.
LightsHow many lights are on, All on, All off, and saving them to the view. See Lights in the walk.
KeysEvery key, as listed above.

A walk nobody touches for two minutes pauses by itself and shows the menu; Walk on continues where you stood. A walk also pauses while its page is hidden.

Look and quality

Clay model draws every material in plain light tones, which works on any project and shows form and light. Materials draws them in their colours and textures. Both have a physical sky, the sun at the project's place and time, soft shadows, and corners and joints that darken as they do in daylight. [ and ] move the sun through the day.

The quality presets trade sharpness and shadows for speed:

PresetUse it for
LowPhones, older tablets and slow computers.
MediumThe start: smooth on most laptops, also on a high-resolution screen.
HighFull sharpness on a high-resolution screen, with more shadows.
UltraFast desktops, and pictures.

On a heavy model, walk mode lowers its resolution a little to keep moving smoothly. A choice you make is remembered for the next walk.

Take a picture

  1. Stand where you want the picture, and press P.
  2. The picture is taken as you see it, at your screen's size, and shown in a panel.
  3. Choose where it goes: Download JPG, Copy to the clipboard, Put on the sheet (pick the sheet), or Save to Files ▸ Exports.
  4. Back to walking continues the walk.

A picture on a sheet can be moved and resized there like any other picture. An assistant connected to Stomra can also take a picture of the walk at a room, a time of day and the view's lights, without changing what is on your screen.

Versions as you walk

Where the project has a history of versions and alternatives, the walk shows it on the left: the model as it is on top, then its named versions, issues, merges and alternatives.

Work orders from the walk

The full guide is Work orders.

For the people who work on the project, O holds the view still and asks what should change at what you aim at, for example "Move this 1 m to the right". Every thing in view carries a number; click one to add it to the order. Enter saves the order and walks on. The order keeps what you aimed at, where you stood and the view as you saw it, so whoever takes it, a colleague or an assistant, knows what "right" meant. G goes to the next open order. The orders are listed under Project ▸ Work orders.

Your client's walk

When you publish an issue to the client portal, it carries the model, and your clients walk it in their browser with the same walk mode, without an account or anything to install.

To publish, open the project's Client portal and choose Publish…; Invite client… sends a client their link. The whole round with clients is in The review flow.

Good to know